Home > Black Screen > Black Screen- Nothing On The Monitor.help!

Black Screen- Nothing On The Monitor.help!

OR 2) inbios check that you have enabled support for any addon cards. if it stillno display, it could be the mobo died, or the monitor died... This will detect any attempts to install viruses that could destroy our entire system in one second! This isn't a big concern if you're careful, so don't worry! Check for causes of electrical shorts inside your computer. Check This Out

No POST Does the computer beep when it is turned on or does it sound like the computer is working? One of the most likely causes is RAM. remove the memory card and power on 5. d.

Continue Reading Up Next Up Next Article Think That DLL Issue is Due to a Hardware Problem? If you end up connecting your monitor the motherboard, it might work for a little bit, but suddenly go blank. it will quite hard to fix failed mobo....

Monitor won't detect/display anymore. f. Step 5: Reseat loose internal components If the computer case was recently serviced or moved, a card, cable, memory module, or processor may have become loose. Rebooted.

Was the information on this page helpful? If that doesn't solve the problem, try another cable. Join our site today to ask your question. why not find out more If you have just installed the computer and nothing seems to work, it could a bad monitor or a low power supply.

If you are like me and none of those work what I did was I changed the PCI port location and moved it to a different motherboard. My new house has some power problem it always low voltage. Hope this helps! Actually when I turned on, it took a long time to get to display & then window was also working weird, then I restarted a couple of time & I though

Check your manual to see what key combination you need. this content Make a boot disk (see http://support.microsoft.com/kb/314503 for instructions for XP) d. So you'll only run into this program if you are using an older version of Windows or a really old monitor. Step 3: Inspect the video cable and video connectors for damage Inspect the video cable and video connectors for damage.

edit: try another repair shop, not judging the shop but it's seems strange.. his comment is here Well the only other system I have is a laptop, so I don't think that would work since I have a computer. If that doesn't work, then you need to check the actual port connectors on the computer and on the monitor for damage. If the monitor is still blank, continue to the next step.

A beep code will give you a very good idea of exactly where to look for the cause of your computer turning off.If you don't resolve the problem by troubleshooting to screen is black. [Solved] (Solved) Can't exit power saving mode Computer will not load past welcome screen [Solved] (Solved) My computer wont go past the acer screen [Solved] (Solved) Helpful +412 If the monitor still displays a black screen or displays a No signal message, the video hardware may be faulty and needs to be replaced or serviced. this contact form Press the Down Arrow key to select Hardware Power Management, then press Enter.

So they have reduced the power of these fans that are used to cool the hardware. If you have a flat panel LCD monitor, unplug the monitor power cable, wait about 30 seconds, reconnect the cable and then turn on the monitor. The computer restarts.

Lastly, you should also make sure that the input source on your monitor is set to the correct input.

Nor is your hard drive. You can choose "Last known good configuration" to go back to the last known safe shutdown state. Check cable from monitor to computer first to make sure it is securely attached.Click to expand... 1) What/where is the "faint box"? 2) Where is the video card located at? Borrow a computer monitor and connect it to your computer.

The mobo is Intel DB85FL. Make sure that you place the computer in a well ventilated room to avoid overheating. No, create an account now. navigate here In the BIOS Setup utility, press the Right Arrow key and select the Power tab.

Once the computer is off, wait a few seconds and then try powering the computer on again. The processor fan is new with brand new heat sink silicone. Helpful +28 Report Ruan Jan 5, 2010 at 12:58 AM Its the motherboard/processor/power supply. Select your current installation and press R to repair the installation. 9.

Reply to joseph santos joseph santosMar 23, 2015, 2:35 AM unplug HDD and blow...remove RAM clean... solved Computer turns on, but monitors display nothing? My motherboard was still getting power and the cpu and gpu fans were still spinning when I pressed power, just no signal to the screen. 3 hours later I got mine d.

One beep is normal, more then one = ERROR 4-Swap monitors to make sure it's not monitor. Disconnect your monitor and connect it to another computer. Go to Reseat loose internal components to check for loose components. Skip to Step 6: Change the display resolution to resolve monitor issues .