Changing the Timeout value in the Boot.ini file does not have any effect. Tried to boot from D drive - same thing. During this phase, Setup completes the following tasks: Determines the basic hardware installed (such as the CPU, motherboard type, and hard disk controllers). Starting the Computer After the computer finishes the POST, the system BIOS attempts to start an operating system.
My Nero refused to do that (it only wanted to do it to CD). Check boot path and disk hardware. The drivers for the IDE controler will not work if changing from say a VIA chip set to Nvidia or SIS etc. When the Settings screen opens, scroll down and click on the Restart now button under the Advanced Startup category and your computer will restart.
Next, Windows Setup will find existing Windows XP/2000 installations. Join our site today to ask your question. These files perform initial hardware detection and then pass control to the kernel, which is loaded along with the boot drivers and the drivers for the hard drive controller(s). Flag Permalink This was helpful (0) Collapse - Thanks by TheDanster21 / March 7, 2012 4:52 PM PST In reply to: Paul Thanks man, this was what i was looking for.
How to install and use the Windows XP Recovery Console The Recovery Console is a special boot up method that can be used to help fix problems that are preventing your If you are unsure whether you have RAID/SCSI, then simply let the CD load without pressing F6. Source: EarthWeb (June 13, 2000) How to Boot Windows 2000-Based Computers When You Use a Debugger Program Microsoft Knowledge Base Article: 295553 - This article describes the commands that you can When done with your tasks, from within Safe Mode, start msconfig.
All rights reserved. So I tried to boot from the DOS disk - same thing - "missing file". Once you're done in Safe Mode, if you want to get back into normal Windows, restart the computer. Logged (\BOOTLOG.TXT) 3.
This section describes the configuration details involved when you start Windows 2000 Professional with MS-DOS. I have found that during boot up right after the computer shows you all the equipment , memory, etc installed on your computer, if you start lightly tapping the F8 key Do whatever tasks you require and when you are done reboot to boot back into normal mode. At the beginning of the GUI-mode phase of Setup, Plug and Play runs to detect all the devices on the system.
No devices are configured by the BIOS In the Advanced Configuration and Power Interface (ACPI) of Windows 98 and Windows 2000, the operating system configures almost all devices. There are a number of issues that can cause a system to fail to boot, and we've tried to list as many as we could find here. Ntldr Cannot Load Fragmented System Hive Microsoft Knowledge Base Article: 265509 - Your computer may stop responding (hang) during startup from a hard disk that uses the NTFS file system if WindowsXP does, however provide a true DOS-like environment for running old DOS programs.
Nov 9, 2003 #11 RyonanGT TS Rookie one question here.... As always it is best to backup everything you want to keep before doing this or a new install. Copies the remaining installation files that were not copied during the text-mode phase of Setup. navigate to this website All partitions that are in use receive a number.
Stop messages If you are installing Windows 2000 and you encounter a Stop message, check the HCL to determine if the computer and its components are supported with Windows 2000 Professional. This disk contains a copy of the system Registry and provides crucial information that you need to use NT Setup's Repair process to locate and repair a damaged NT installation. Configures each device, and installs and configures networking components.
Figure 11. When GUI-mode has completed these tasks, it starts the operating system and presents the Winlogon screen. i was told i would have to reinstall windows but i dont want to lose my data cause i love it so (ahem porn ahem). Understanding the Boot.ini Naming Convention Windows 2000 uses the Advanced Reduced Instruction Set Computing (RISC) naming convention to define the path to a Windows 2000 installation.
These are not linear memory locations but numerical pointers or representations of physical memory locations. Type msconfig in the Open: field. The only one that it selects is connect using a broadband connection. If this problem occurs, you can press any other key to resume the startup process.
Additional file system considerations include: NTFS partitions are not available to users running Windows 95, Windows 98, Windows 3.x, or MS-DOS. This problem can occur if the System hive is equal to or greater than 16 megabytes (MB). Configure your computer to create a multiple-boot system by using Windows 2000 Professional with other operating systems. is it the same as formatting ur pc when using the method u list out here????Click to expand...
Configuring a Multiple-Boot System with Windows 95, Windows 98, or Windows NT 4.0. Bootstrap Loader Process Ntldr loads the operating system files from the boot partition. Each time the system is started in a dynamic configuration, the devices are reexamined. The Plug and Play Manager determines the hardware resources requested by each device (for example, I/O ports, IRQs, DMA channels, and memory locations) and assigns them appropriately.
Review the detailed description about how to set up a multiple-boot system by using Windows 2000 Professional with Microsoft® Windows NT® 4.0, Microsoft® Windows® 95, Microsoft® Windows® 98, and Microsoft® MS-DOS®. Table 6.4 Multiple Boot Considerations Operating System Combinations Considerations Windows 2000 and Windows NT 4.0 Install operating systems on different partitions. Installs any optional components. The system can sometimes stop responding during this phase.
This section discusses how to create Setup and startup disks as well as some frequently asked questions about common Setup problems. When the computer is turned on the next time, Windows should notice that the computer did not successfully boot and give you the Safe Mode screen. It is in these situations that using the System Configuration utility to boot into safe mode can cause the computer to become inoperable for many users. Click here to join today!
From the boot loader screen you can choose to start Windows 2000 Professional or another operating system. Dec 8, 2003 #14 NoisySilence TS Rookie Posts: 98 Install Recovery Console to boot menu It's a sticky thread too. Newer versions will work as well (ie. Please help.
HOW TO: Determine if it Is Possible to Start Windows 2000 with the Keyboard Unattached Microsoft Knowledge Base Article: 320466 - This step-by-step article describes the issues that are related to Ask !