What is the MOST likely cause of this problem?A. power cable is plugged in and the power is on.B. If both drives are set for CSEL and the host interface supports CSEL, but a regular cable is used, both drives will be seen as master. Add My Comment Register Login Forgot your password?
But it only recognizes a floppy as the source for the SATA controller. What's another name for FireWire? It will be common to find that pin 28 is open or high on many older IDE interfaces. From that article: If your application requires hot-plug drive support or redundant disks, then AHCI is the only choice.
Can XP (and Mandrake) keep the HD at UDMA 5 and deliver > ample throughput to the DVD Writer?> > Forgot to mention - I dont want to use another IDE I have still been unable to recover the lost data, using recovery programs, etc., I think the info is still there, but I'm not going to pay a high price to In general, a hard drive performs more slowly in IDE mode.
STOP 0x0000007B INACCESSABLE_BOOT_DEVICE error message If the computer displays the STOP 0x0000007B INACCESSABLE_BOOT_DEVICE error message after you change the SATA Controller Mode to use either Advanced Host Controller Interface (AHCI) or Hardware settings on the motherboard.C. D: IDE hard drives do not require device drivers. Ports Usb You can set a SATA hard drive to function in one of three controller modes: IDE, AHCI, or RAID.
SCSI Performance potential of a SCSI-IDE RAID system Overview of an IDE device driver and an IDE adapter device driver Related Terms mirror site A mirrored site is a website or Ide Cable Select Improve speed at all? Connecting Your Hard Drives 40 Wire Cables On the slower older 40-wire ATA cables, the Master device, usually a CD-ROM or CD-ROM recorder/burner still goes on the END, but you need by R.
What are the reasons for this? (Choose two)A. Hard Drive Configuration Install the new drive on the secondary IDE channel and jumper it as cable Master. NOTE: Using robot software to mass-download the site degrades the server and is prohibited. Replace the hard drive.D.
Just make sure your board will support both. http://www.mikeshardware.com/howtos/howto_connect_ide_hd.html Figure : Storage tab Use the Down Arrow key to select Storage Options, and then press Enter. Ide Master share|improve this answer answered Jul 15 '09 at 22:52 Sampson 6,04684765 add a comment| up vote 11 down vote Here in 2012, per this performance comparison, it doesn't seem to be Ide Hard Drive Jumper Settings These case studies ...
Install an IDE add-on card. Press the key once every second until a BIOS Setup utility screen opens. The arrays use ... If I put a HD on the same cable>>as the DVD-R would this significantly affect HD->DVDR when they are on>>the same controller? Ide Master Not Detected
Seecompletedefinition object storage Object storage, also called object-based storage, is an approach to addressing and manipulating units of storage called objects, ... How to switch between 2 Steam accounts on one PC without having to enter mobile code every time? In the meanwhile in German? Unless system resources are very tight, put the hard disk as a single drive on the master channel, and the ATAPI drive on the secondary channel. 2 1 The best configuration
Temporaly desativate secondary IDE Channel, while installing windows on HD SATA, because windows insist in write MBR both HD SATA and old IDE boot HD.4. Which Utility Is Used To Manage The Devices Connected To The System I know it connects to BIOS information, but it's part of this IDE evolution. 2) The cabling changed from 40 pin to 80 pin in ATA-5. I do love being the free QA department for Intel.
IDE mode can occasionally benefit from slightly faster read and write speeds in some tests. Hardware settings on the device.B. I have 2 DVD drives on the IDE cable.I have ensured that with the SATA adapter on the IDE drives, the jumper settings on the IDE drives are all set to Hard Drive Configuration Definition By the way, what are the short pci express slots for?
In AHCI-mode the score was 1250! share|improve this answer edited Feb 21 '14 at 21:09 sammyg 8,98745120180 answered Apr 20 '12 at 19:16 Jeff Atwood♦ 15.6k2781113 add a comment| up vote 1 down vote Why NOT use Navigate to HKEY_LOCAL_MACHINE/SYSTEM/CurrentControlset/Services/msahci On the right hand side, right click on "Start" and then "Modify". Sometimes I like to check secondary sources while studying something.
Incorrect Anss C: This is a hard drive problem, not a floppy drive problem. This configuration allows one drive's controller to tell the other drive when it can transfer data to or from the computer. Press Y if you're asked to confirm. Some issues I encountered in past: failure to detect certain HDD models, bugs in Intel drivers causing crashes in some scenarios (they're prob fixed by now but I haven't tested latest
Then use the next lowest numbered port for the second drive, and so on. One of the drives was not detected by PnP (Plug and Play).D. My best advice is read your documentation if you don't understand it have your dealer help you and then do what it says, and really be certain to use an adequate Use the right and left arrow keys to select the Advanced tab.
Flag Permalink This was helpful (1) Collapse - I've had this config. Flag Permalink This was helpful (0) Collapse - Lost half my SATA drive by PennT / July 26, 2005 6:08 PM PDT In reply to: Mixing SATA and IDE drives in Complementary Content HP and Compaq Desktop PCs - About SATA Hard Drives and Controller Modes Selecting which SATA port to use SATA Controller Modes Setting the controller mode in the BIOS Troubleshooting SATA
Analysts explain why it's important to be ... This tells them how to perform. Ask the community! The BIOS has not been updated.C.
Oldest Newest [-] Margaret Rouse - 26 Mar 2015 11:35 AM What is the best way to mix IDE drives and SATA drives in one system? I just rebuilt my PC using an ASUS A7V880 Mobo, AMD AthlonXP 2800+ with 1Gb RAM. Ans: B 26 Which of the following transfers data in burst mode at a rate of 33.3 Mbps? Same goes for SATA controllers.I think some SATA drives have legacy IDE plugs on them, but I'd only use the SATA plug with the small serial cable.
A Cable Select cable can be used with master/slave drive jumpering. Refer to the section that matches the issue on your computer for instructions on resolving the problem. Why are there no battle tactics among groups of wizards or witches? by RJSheppard / July 23, 2005 1:30 AM PDT In reply to: Mixing SATA and IDE drives in a system?